Engineering & Inventions · Buildings & infrastructure

Skyscrapers

A tall building is limited less by its weight than by wind, elevators and money. See what made the first skyscrapers possible in 1880s Chicago, how today's towers fight the wind, and what sets the height record.

4 short lessons · about 16 minutes · 9 sources · updated November 2026

What you will learn

  • Explain why load-bearing brick walls limit a building's height and how a steel frame removes that limit
  • Describe how Otis's safety elevator made the upper floors of a tall building usable
  • Explain why wind becomes the main load on a very tall building and how a tube structure resists it
  • Describe how a tuned mass damper reduces a tower's sway

Lesson 1 of 4 · 4 min

The steel frame and the elevator that wouldn't fall

Before you readChicago's Monadnock Building, begun in 1891, holds up 16 floors on brick walls. Why did builders almost stop making brick towers that tall after it?

Correct.Not quite. The answer is The bottom walls had to get too thick.

A brick wall carries everything above it, so a taller wall needs a fatter base. The lesson shows how a steel frame got around that.

The Monadnock Building in Chicago has 16 floors of offices, and its brick walls hold the whole thing up. When it went up in the early 1890s, those load-bearing walls were the tallest of any office building in the world.

A load-bearing wall carries the weight of every floor above it. So the bricks at the bottom carry the most, which means the wall has to thicken toward the base. Go higher and the ground floor fills with wall, leaving less room to rent and smaller windows.

Chicago had already found the way out. The 10-story Home Insurance Building, finished in 1885, stood on a steel skeleton. The frame carried the full weight of the walls, floor by floor, so the outer wall became a thin curtain hung on the frame.

Check yourselfIn a steel-frame skyscraper, what holds up the outer walls?

Correct.Not quite. The answer is The frame, at each floor.

The frame carries the wall's weight floor by floor, so the wall is a curtain and doesn't need a thick base. In a brick tower, each wall rests on the wall below it.

A tall frame is useless if nobody wants to climb to the top. Most people won't walk up more than a few flights of stairs, and early hoists hung on a single rope. If the rope broke, the car fell.

Elisha Otis built a safety elevator that halts by itself if the hoisting rope breaks. He showed it off at New York's Crystal Palace in 1854. In 1857 the Haughwout store in New York installed the first passenger safety elevator.

Today's elevators keep his idea. A car hangs from several cables, and each one can hold the full load plus 25%. If the car still drops too fast, a device called a governor clamps brake shoes onto the rails in the shaft.

Try to recallWhy did skyscrapers need a safe elevator as much as they needed a steel frame?

A frame lets you build twenty floors, but people won't climb that many stairs, so the top floors would sit empty. A plain hoist could fall if its rope broke. Otis's safety elevator stopped by itself when the rope failed, which made the upper floors safe and easy to reach.

Brick walls stop around sixteen floors because their bases grow too fat. A steel frame carries the walls instead, and a safety elevator gets people to the top, which together made the skyscraper.

Lessons in this topic

  1. The steel frame and the elevator that wouldn't fall

    Why brick buildings stalled at about sixteen floors in 1880s Chicago, and the two inventions that let them keep climbing.

    Essentials · 4 min

  2. Why wind, not weight, shapes the tallest towers

    How Fazlur Khan's tube design stiffened towers against wind with less steel, and how a giant pendulum keeps Taipei 101 from swaying too much.

    Essentials · 4 min

  3. How you build a tower half a mile high

    Follow the Burj Khalifa from its piles to its top floors, and see how concrete, steel and cranes get hundreds of meters up.

    Deeper · 4 min

  4. What really stops towers getting taller

    Why elevators and rent decide a tower's height more than engineering does, and how spires and official rules shape the race to be tallest.

    Deeper · 4 min

Three quick stories from this topic

The Burj Khalifa's empty top

The top 244 meters of the Burj Khalifa are a spire nobody can live or work in

Without the spire the tower would stand about 585 meters tall. A study by the body that ranks tall buildings noted the empty spire could be a skyscraper on its own.

Why build it

Official rankings measure to the architectural top, which counts spires. An empty spire adds height to the record without adding floors.

Vanity height

The unusable space above a tower's top floor is called vanity height. In supertall buildings it averages about 30% of the height.

Concrete pumped 606 meters

Builders of the Burj Khalifa pumped wet concrete 606 meters straight up a pipe

It set a record for a building. In summer the crews mixed ice into the concrete and poured at night, because Dubai heat can reach 50 degrees Celsius and hot concrete cracks.

A pump built for it

A pump maker built a special high-pressure trailer pump for the job, because most of the tower is reinforced concrete.

Why cool it

Cooler concrete cures more evenly, so it's less likely to set too fast and crack under the tower's weight.

Taipei 101's steel ball

Taipei 101 hangs a 660-tonne steel ball near its top to stop it swaying

The ball is 5.5 meters across and hangs like a pendulum from the 92nd floor to the 88th. Tuned to the tower's own sway, it swings against each gust and cuts the movement by up to 40%.

Why it's there

Taipei gets typhoons and earthquakes. A stiff tower still sways, and the people on the top floors can feel it.

Why tuning matters

A damper only works if its swing matches the building's rhythm. Then it moves against the sway instead of with it.

Sources

  • How bridges carry a load

    Trace weight through beams, arches, cables and supports, and see why shape matters as much as material.

    4 lessons · 15 min

  • Why a strong column still folds

    A column can fold sideways while its material is nowhere near its limit. See what buckling is, why length and end supports matter more than strength, and where engineers let it happen on purpose.

    4 lessons · 24 min

  • How buildings stand up

    Every building has to carry its own weight, its contents and the wind down to the ground. Follow those loads through floors, beams, columns and foundations, and see what the soil underneath has to do.

    4 lessons · 16 min

  • How a heat pump moves heat

    See how a machine warms a house with heat taken from freezing outdoor air, follow its refrigerant around the loop, and learn to read the performance number on its spec sheet.

    4 lessons · 16 min

  • Why a system with backups still fails

    Every defense has holes, and the holes move. See why an accident needs several of them to line up, how spare parts make failure look almost impossible on paper, and how a backup can leave a system less safe.

    4 lessons · 21 min

  • Simple machines and mechanical advantage

    Levers, pulleys, ramps, wedges, screws and wheels all trade distance for force. See how each does it, why none saves any work, and how to find them inside a bicycle or a crane.

    4 lessons · 16 min

All engineering & inventions topics · Take the quiz